How to read a well water test report
Last checked November 18, 2026
How to read a private well water lab report, compare results to EPA drinking-water benchmarks, and decide what to do next.
A private well is the well owner’s responsibility. The federal rules that protect public drinking-water systems do not apply to most private wells, and officials do not routinely test or treat that water for you.[1][2] The laboratory report is how you find out what was measured and how those numbers compare with national health and aesthetic benchmarks.
This page summarizes official guidance we fetched on November 18, 2026. If a source page later changes, follow the official page. This is not a lab report and not medical or legal advice.
What a report should show
The U.S. Environmental Protection Agency (EPA) says your water test results should include the concentration of each substance you tested for. The report may also say whether that concentration exceeds a national primary or secondary drinking-water standard. If the laboratory does not make that comparison, EPA points you to its list of drinking-water contaminants and their Maximum Contaminant Levels (MCLs).[3]
The Illinois Environmental Protection Agency, writing for private well users, adds two useful cautions: the presence of a contaminant does not necessarily mean your health is in danger, and levels greater than the relevant standard can indicate a potential problem. Illinois EPA also says your local health department can help explain the results and describe treatment options.[4] The Centers for Disease Control and Prevention (CDC) likewise says your health department can help you understand the results and what to do next.[2]
Units you will see
Most chemical results on EPA’s national primary standards table are in milligrams per liter (mg/L).[5] Some radionuclide results are reported differently: uranium is listed as 30 micrograms per liter (µg/L), and radium and gross alpha are listed in picocuries per liter (pCi/L).[5]
North Dakota State University Extension, in a publication we fetched, defines mg/L as the same as parts per million (ppm) and µg/L as the same as parts per billion (ppb).[6] If one report uses ppm and another uses mg/L, those two ways of writing the same number can be compared directly.
Primary standards versus secondary standards
When a report mentions an “MCL” or a “health standard,” it is usually referring to EPA’s National Primary Drinking Water Regulations. Those MCLs are legally enforceable limits for public water systems. They are set to limit contaminants that can affect health. EPA also publishes a Maximum Contaminant Level Goal (MCLG), which is a non-enforceable health goal.[5] Those public-system numbers are not a legal limit on a private well, but EPA tells private well owners to use them as a reference when a lab report is not already compared to the national standards.[3][4]
Secondary maximum contaminant levels (SMCLs) are different. EPA sets them as non-mandatory guidelines to help public systems manage taste, color, and odor. EPA does not enforce SMCLs, and it states that these contaminants are not considered to present a risk to human health at the SMCL. Iron (0.3 mg/L) and manganese (0.05 mg/L) are examples: the SMCL is about rusty or black staining and metallic taste, not an enforceable health MCL.[7] For manganese, EPA has also issued a separate, non-enforceable health advisory at a higher concentration; that is explained in the iron and manganese topic guide.
How bacteria results are usually written
Bacteria tests are often reported as present (positive) or absent (negative), not as a concentration. Illinois EPA says state and local health departments look for the presence or absence of coliform bacteria, and that a positive test indicates the well may need to be modified or fixed.[4]
The Missouri Department of Health and Senior Services (DHSS) describes the outcomes this way in its explanation of private drinking-water results:[8]
- Total coliform and E. coli absent — the sample is considered satisfactory for drinking-water purposes.
- Total coliform present — the sample is unsatisfactory. Coliforms in drinking water mean contamination has occurred and other disease-causing bacteria could also be present.
- E. coli present — the sample is unsatisfactory. E. coli means fecal contamination has occurred, and the health risk may be higher because other bacteria from feces may have entered the supply.
- Unsatisfactory for testing — the laboratory rejected the sample (wrong container, more than 48 hours in transit, chlorine in the sample, less than 100 mL, incomplete paperwork, or not a drinking-water source).
CDC’s general testing guidance is consistent with that reading: total coliforms are used as an indicator that harmful germs may also be in the water, and a positive test for fecal coliforms or E. coli likely means feces have gotten into the well.[2] EPA’s national standards table likewise says total coliforms are not a health threat in themselves; they indicate whether other potentially harmful bacteria may be present. Fecal coliforms and E. coli come from human or animal fecal waste.[5]
A favorable bacteria result is not, by itself, proof that every chemical in the water is acceptable. It only answers the bacteria question you asked the laboratory to run.
What to do with the numbers
- Confirm you understand the units and the benchmark. Match each result to the EPA MCL or SMCL, or to any state health-department explanation that came with the report.[3][4]
- If a result is above a health standard, or bacteria are present, stop and get help interpreting it. CDC says to consider drinking bottled water or water from another safe source if results show harmful germs or chemicals, and to contact your local health or environmental department. That office can tell you what to do next and may recommend testing more often.[2]
- Retest to confirm. EPA says that if a contaminant exceeds health standards, you should contact your public health department for specific steps and have the well retested to confirm the contaminant and its concentration.[3]
- Do not assume boiling will fix a chemical problem. CDC states that boiling will not remove chemicals from water. Boiling is a way to kill germs when you cannot use another safe source.[9]
Use a state-certified laboratory for the tests that matter for drinking water. EPA and CDC both say to use a laboratory certified to do drinking-water testing; your state certification program or local health department can point you to one. EPA also notes that it cannot test residential well water on request.[3][2][10]
When to call a professional
Call your local or state health department if you cannot tell whether a result is a problem, if bacteria are present, or if a chemical is above an EPA health benchmark.[2][4]
Call a licensed or certified well or pump contractor if the report, or a well inspection, points to a construction or equipment problem — for example a damaged cap or casing, surface drainage toward the well, or bacteria that remain after proper disinfection.[3][8]
For treatment equipment, CDC says to contact your health department or a well water contractor to help decide the best option. No single treatment type protects against every problem, and a system should be chosen for the contaminant you actually have.[9]
This guide is a reading of official pages, not personal medical advice. If someone in the household is ill, pregnant, or nursing, or if an infant drinks the water, contact your clinician and your local public health agency.
Sources
All of the following were fetched on November 18, 2026 (checked Nov 18, 2026).
- EPA, Private Drinking Water Wells — checked Nov 18, 2026
- CDC, Guidelines for Testing Well Water — checked Nov 18, 2026
- EPA, Protect Your Home’s Water — checked Nov 18, 2026
- Illinois EPA, Interpreting Test Results (private well users) — checked Nov 18, 2026
- EPA, National Primary Drinking Water Regulations — checked Nov 18, 2026
- North Dakota State University Extension, Iron and Manganese Removal (WQ1030, revised December 2025) — checked Nov 18, 2026
- EPA, Secondary Drinking Water Standards: Guidance for Nuisance Chemicals — checked Nov 18, 2026
- Missouri DHSS Bureau of Environmental Epidemiology, Explanation of Private Drinking Water Test Results — checked Nov 18, 2026
- CDC, Guidelines for Treating Well Water — checked Nov 18, 2026
- EPA, Contact Information for Certification Programs and Certified Laboratories for Drinking Water — checked Nov 18, 2026