How to shock-chlorinate a well
Last checked November 18, 2026
Official CDC and state-health steps for disinfecting a private well with unscented household bleach, including safety limits and when to hire a contractor.
Shock chlorination is a one-time disinfection of a well and the household plumbing with a strong chlorine solution. Health agencies recommend it after a bacteria problem, after certain repairs, or after a well has been flooded. It is not a substitute for fixing a cracked seal, a poorly constructed well, or a contaminated water source, and it will not make water safe if the problem is fuel or other toxic chemicals.[1]
This page summarizes official guidance we fetched on November 18, 2026. Procedures differ slightly by agency. Follow your state or local health department if it publishes its own instructions, and follow the official page if a source later changes.
Safety first — and when to hire a contractor
CDC’s well-disinfection page is written for wells after an emergency such as a flood, but it is the federal step-by-step procedure we found for disinfecting a private well with household bleach. CDC’s first points are about safety, not bleach amounts:[1]
- Contact your local or state health department or agriculture extension agent for specific advice, and check with local authorities before you start.
- Wells should be disinfected by a well or pump contractor, due to safety concerns.
- Turn off electricity to the well area before clearing debris. Do not repair the water system unless you are experienced with this work; electrical shock can occur.
- Do not enter a well pit. Gases and vapors can build up there.
- Before power is turned back on, a qualified electrician, well contractor, or pump contractor should check the equipment wiring.
- Wear protective goggles or a face shield when working with chlorine. Chlorine solutions can injure the eyes, irritate skin, and damage clothing. Work in a well-ventilated area and avoid breathing vapors.
- Warn users not to drink or bathe in the water until all disinfection steps are finished.
If the well was flooded, EPA also says to stay away from the well pump while it is flooded, not to drink or wash from the flooded well, and to get assistance from a well or pump contractor to clean and disinfect the well before turning the pump on.[2]
If you are not comfortable with electrical work, confined spaces, or handling concentrated bleach, hire a licensed or certified well or pump contractor and stop here.
What you need to know before adding bleach
Use only unscented household liquid chlorine bleach. CDC says typical bleach concentrations are generally between 5 and 9 percent, and that the amounts in its tables are approximate, rounded to a practical measurement, and calculated to reach a chlorine concentration of more than 100 mg/L.[1]
Bypass or close valves to a water softener before you circulate the chlorine. CDC warns that the disinfection process may damage softeners because of the large amount of chlorine; follow the manufacturer’s instructions, and you may need to keep the unit bypassed until disinfection is finished.[1]
Missouri DHSS’s disinfection instructions add another practical limit: do not dump large amounts of bleach water into a septic system, because it can upset the bacterial action in the tank. Flush as much of the chlorinated water as possible onto the ground instead.[3] CDC likewise says to drain chlorinated water onto an area without plants or vegetation, such as a driveway, and to avoid draining into streams, ponds, or other open water.[1]
You will need a safe drinking-water supply for the hold time and until a certified laboratory result comes back.
CDC procedure for a drilled or driven well
After checking with local authorities, CDC’s steps for a drilled or driven well are:[1]
- If the well has an electrical pump, turn off the electricity and clear debris from around the top of the well.
- Repair the electrical system and pump if needed, or call a qualified contractor.
- Start the pump and run water until it is clear, using the outside faucet closest to the well so unsafe water stays out of indoor plumbing. If there is no pump, bail water until it is clear.
- If the well is connected to indoor plumbing, close valves to any water softener.
- From CDC’s table (below), measure the unscented bleach for your casing diameter and depth of water. Mix that bleach with 3 to 5 gallons of water in a 5-gallon bucket.
- Remove the vent cap. Pour the mixture into the well with a funnel, avoiding electrical connections. Attach a clean hose to the nearest outside faucet and circulate water back into the well to mix.
- Rinse the inside of the well casing with a garden hose or bucket for 5 to 10 minutes.
- Open all indoor faucets and run the water until you notice a strong chlorine (bleach) odor at each faucet. Turn the faucets off and leave the solution in the well and plumbing for a minimum of 12 hours.
- After at least 12 hours, attach a hose to an outside faucet and drain the chlorinated water onto a driveway or other area without vegetation, until the chlorine odor disappears. Then run indoor faucets until the chlorine odor disappears.
CDC publishes a separate table for bored or dug wells, which it says can be difficult to disinfect because they are often shallow and poorly protected. If contamination continues in a bored or dug well, CDC says to consider upgrading the well or drilling a new well.[1]
Approximate unscented bleach for a drilled or driven well (CDC)
CDC’s table (household bleach, 5–9 percent, to reach more than 100 mg/L chlorine) includes these example amounts. Use the official table for the depth and diameter that match your well.[1]
| Depth of water | 4-inch casing | 6-inch casing | 8-inch casing |
|---|---|---|---|
| 20 feet | 6 1/2 tablespoons | 1 cup | 1 1/2 cups |
| 50 feet | 1 cup | 2 1/2 cups | 3 3/4 cups |
| 100 feet | 2 cups | 5 cups | 7 1/2 cups |
These figures are CDC’s approximations, not a substitute for the full table or for a contractor’s calculation.
State procedures may use a different hold time
Hold times are not identical across official pages. CDC’s minimum is 12 hours.[1] Missouri DHSS’s Disinfecting Your Private Water Well instructions tell the owner, after chlorine is smelled at the taps, not to run water for six to eight hours.[3] University of Missouri Extension’s 2018 flood-well note uses at least eight hours and a different bleach recipe.[4]
We are not combining those recipes. If your state health department publishes a disinfection procedure, follow that procedure, or hire a licensed well contractor to do the work.
After you flush the chlorine
CDC’s sampling guidance is:[1]
- Until the well has been tested, boil the water (rolling boil for 1 minute) or use another safe source.
- Wait at least 7 to 10 days after disinfection to sample, and only after chlorine has been thoroughly flushed.
- Use a certified laboratory. Your local health department, your state laboratory certification officer, or EPA’s Safe Drinking Water Hotline (800-426-4791) can help you find one.
- Test for total coliform and either E. coli or fecal coliform.
- If those results show no coliforms, CDC says the water can be considered safe to drink.
- Retest in the next 2 to 4 weeks and again in 3 to 4 months. Over the longer term, monitor bacterial quality at least twice a year, or more often if the water changes.
If coliform bacteria are still present, repeat the disinfection and test again. If tests continue to show bacteria, contact your local health department.[1] Persistent bacteria often mean a construction or location problem, not a need for more bleach.
When to call a professional
Hire a licensed or certified well or pump contractor (and an electrician if wiring may be wet or damaged) if the well was flooded, if you are not experienced with this work, if you would rather not handle chlorine, or if bacteria remain after a proper disinfection.[1][2] EPA also says to hire a certified well driller for construction, modification, or proper abandonment of a well.[2]
This guide is a reading of official pages, not a substitute for a licensed well contractor or for your health department’s instructions. Chlorine solutions and well electrical systems can cause serious injury.
Sources
All of the following were fetched on November 18, 2026 (checked Nov 18, 2026).
- CDC, How to Disinfect Wells After an Emergency — checked Nov 18, 2026
- EPA, Protect Your Home’s Water — checked Nov 18, 2026
- Missouri DHSS, Disinfecting Your Private Water Well — checked Nov 18, 2026
- University of Missouri Extension, Use shock chlorination to disinfect contaminated wells (March 26, 2018) — checked Nov 18, 2026