Lead from household plumbing in well water
Last checked November 18, 2026
How lead gets into private well water from plumbing and well components, why EPA’s health goal is zero, and what official sources say to do after a test.
Lead in drinking water usually comes from pipes, solder, faucets, and fixtures, not from the well water as it leaves the ground. Corrosion — a chemical reaction between the water and metal plumbing — can dissolve lead into the tap water, especially when the water is acidic or low in minerals.[1][2] You cannot see, taste, or smell lead in water. Testing is the only sure way to know whether it is present.[1]
This page summarizes official guidance we fetched on November 18, 2026. If a source page later changes, follow the official page. This is not medical advice.
Where lead comes from in a private well system
EPA says the most common sources of lead in drinking water are lead pipes, faucets, and fixtures. Homes built before 1986 are more likely to have lead pipes or lead solder. Even in homes without a lead service line, brass or chrome-plated brass faucets and lead-soldered plumbing are a common problem.[1] CDC adds that household plumbing fixtures, welding solder, and pipe fittings made before 1986 may contain lead, and that galvanized iron pipes can also be a source.[2]
On a private well, CDC also names two well-specific sources: “packer” elements in private wells that are 20 years old or older, and leaded brass parts in older submersible pumps. CDC’s advice is to check both the well and the pump, and to have a licensed well water contractor help determine whether any of the well’s parts are a source of lead. Remove the lead source if possible.[3]
EPA tells private well owners to test for pH, lead, and copper if household plumbing or service lines contain lead, and to test for corrosion, pH, and lead if pipes are corroding.[4] How much lead enters the water depends on the water’s acidity and mineral content, how long the water sits in the pipes, water temperature, how much lead the water touches, wear in the pipes, and whether protective scales have formed inside the plumbing.[1][2]
The Safe Drinking Water Act now limits what may be sold as “lead-free” plumbing to a weighted average of 0.25 percent lead across the wetted surfaces of pipes, fittings, and fixtures, and 0.2 percent for solder and flux. That is a limit on new products, not a guarantee that older plumbing in a house is lead-free.[1]
Health effects and official levels
EPA has set the maximum contaminant level goal (MCLG) for lead at zero because lead is a toxic metal that can be harmful even at low exposure levels. Lead persists and can accumulate in the body over time. The MCLG is a non-enforceable health goal, not a private-well standard.[1] CDC states that no safe blood lead level has been identified for young children, and that all sources of lead exposure for children should be controlled.[2]
Young children, infants, and fetuses are particularly vulnerable. EPA links even low blood lead levels in children to behavior and learning problems, lower IQ and hyperactivity, slowed growth, hearing problems, and anemia. During pregnancy, stored lead can be released from bone and can cross the placenta. Infants who drink formula mixed with lead-contaminated water may get a large share of their lead exposure from that water. EPA estimates that drinking water can make up 20 percent or more of a person’s total lead exposure, and 40 to 60 percent for infants who consume mostly mixed formula.[1] CDC also notes that lead in drinking water can harm children’s brains and increase the risk of miscarriage.[3]
The Lead and Copper Rule action level that appears on EPA pages we fetched is 0.015 mg/L (15 ppb, or 15 µg/L). That number is a treatment-technique trigger for public water systems. It is not a standard for establishing a safe level of lead in a home, and it does not legally apply to most private wells.[5][6] Connecticut DPH uses 15 µg/L as its action level for private wells; that is a state benchmark, not a federal private-well MCL.[7] Because EPA’s health goal is zero, a result below 15 ppb is not the same as “no lead” or “no concern.”
Bathing and showering should be safe for adults and children even if the water contains lead over EPA’s action level, because human skin does not absorb lead in water. EPA notes that unusual cases, such as highly corrosive water, may need extra advice from the local health authority.[1][2]
What to do
Test at the tap, using a state-certified drinking-water laboratory and the sampling instructions it provides. CDC says to use your state’s approved sampling protocol, or EPA’s protocol if the state does not have one, because the way the sample is collected matters.[8] Connecticut DPH recommends comparing a first-draw sample (water that has been sitting in the pipes) with a flushed sample, which helps show whether household plumbing is adding lead.[7]
Until you have a confirmed plan, official sources describe these exposure-reduction steps:
- Use only cold water for drinking, cooking, and making baby formula. Hot or warm tap water can contain more lead. Boiling does not remove lead and is not a treatment for it.[1][2][5]
- Run the water before using it for drinking or cooking if it has been sitting in the pipes. CDC’s well-focused page describes flushing for 1–2 minutes before first use for drinking or cooking.[8] Connecticut DPH similarly describes flushing the cold-water tap for at least one minute.[7] EPA notes that the useful flush time depends on the plumbing, and that cleaning the faucet screen (aerator) can also help because lead particles can collect there.[1]
- Use a point-of-use filter certified to remove lead. CDC says to look for independent certification to NSF/ANSI 53 for lead removal and NSF/ANSI 42 for particulate removal. Install and replace the cartridge on the manufacturer’s schedule, and do not run hot water through the filter.[2][1][5]
- Remove the source when you can: lead pipes, solder, fixtures, or lead-containing well or pump parts, with help from a licensed well contractor or plumber.[3][7]
If a child’s exposure is a concern, contact a clinician. CDC says most children and adults with lead exposure have no symptoms, and that a blood lead test is the way to tell whether someone has been exposed. CDC recommends public health action when a child’s blood lead level is 3.5 micrograms per deciliter (µg/dL) or more.[2][1]
When to call a professional
Call your local or state health department for help interpreting a lead result, choosing a certified laboratory, or deciding whether corrosive water (low pH or soft, aggressive water) needs treatment.[4][7]
Call a licensed well water contractor to inspect older pumps, packers, and well fittings for lead-containing parts, and a licensed plumber to identify or replace lead pipes, solder, or fixtures.[3] If a child may have been exposed, contact a clinician about a blood lead test.[2]
This guide is a reading of official pages, not personal medical advice. If someone in the household is ill, pregnant, or nursing, or if an infant drinks the water, contact your clinician and your local public health agency.
Sources
All of the following were fetched on November 18, 2026 (checked Nov 18, 2026).
- EPA, Basic Information about Lead in Drinking Water — checked Nov 18, 2026
- CDC, About Lead in Drinking Water — checked Nov 18, 2026
- CDC, Chemicals That Can Contaminate Tap Water — checked Nov 18, 2026
- EPA, Protect Your Home’s Water — checked Nov 18, 2026
- EPA, Frequent Questions About Lead in Drinking Water — checked Nov 18, 2026
- EPA, Lead and Copper Rule — checked Nov 18, 2026
- Connecticut Department of Public Health, Lead in private well water — checked Nov 18, 2026
- CDC, Groundwater Corrosivity and Lead in Wells — checked Nov 18, 2026